Yard report, updated weekly

Reconciling a steel mill certificate against what's stacked in the yard

Close-up of stacked rusty steel reinforcing bars in a yard

A mill certificate tells you what the mill made. It doesn't tell you what's stacked in your yard this morning, and that gap is where a lot of reconciliation headaches start. The cert is correct for the heat it describes. The question a project controls team has to answer is whether the bundles tagged against that heat are the ones physically stacked between the rebar racks and the aggregate piles, in the quantity the invoice says you paid for.

What the mill cert certifies

A mill test report (MTR) ties a heat number to chemistry results and mechanical properties for one melt of steel. Everything rolled from that heat gets the same heat number stamped or tagged on it, whether it ends up as #4 bar or #11 bar, straight lengths or bundles. The cert is a quality document. It says the steel meets spec. It says nothing about count, and nothing about which truck it rode in on or which corner of the yard it landed in.

That's the part that trips people up. A supplier can hand you a clean cert for 40 tons of heat number 3X4521 and still have shorted you two bundles on the delivery itself. The cert and the packing list are two different documents answering two different questions, and reconciling against the yard means checking both against what's physically there.

Where the mismatch usually shows up

Three places, in order of how often we hear about them:

Bundle count on the tag versus bundle count received. Mill tags list bar size, length, heat number and bundle weight, but a bundle that shifted or broke open in transit can lose its tag, get re-banded on site without a new tag, or get double-counted if a partial bundle gets folded into the next load.

Heat lot splitting across deliveries. A single PO often draws from more than one heat, especially on a job that's pulling tonnage over several weeks. If your invoice bills against a blended heat lot but your yard tally was done bar-size by bar-size without tracking heat number, you can't verify which cert covers which stack.

Stock that's been there a while losing its paper trail. Rebar that's been sitting in the yard for a few weeks tends to lose tags to weather, forklift traffic, or just getting restacked by a crew trying to make room. By the time an auditor or an owner's rep asks for heat lot verification on a specific stack, the tag that would answer the question is gone.

A reconciliation sequence that holds up

  1. Start from the invoice, not the yard. List every heat number and bundle count the invoice bills you for before you walk out to look at anything.
  2. Match each heat number to its MTR. Confirm the cert exists and covers the grade and size the invoice claims. A missing cert for a heat number on the invoice is a flag on its own.
  3. Walk the stacks and read tags, not piles. Count bundles by tag, not by eyeballing a stack height, and note which tags are missing or illegible.
  4. Reconcile count against invoice quantity, heat by heat. A shortage on one heat paired with an overage on another usually points to a mis-tagged delivery. The count tells you which heat to chase down before you escalate it as a billing dispute.
  5. Flag anything untagged as unverified stock, separate from reconciled tonnage, until someone can trace it back to a delivery ticket.

That sequence works. It's also a half-day of a controls manager's week per yard, done with a clipboard and a tape measure for everything that isn't rebar: bundles of pipe, stacked precast, aggregate piles you're estimating by eye. A weekly yard count that lines up bundle numbers against the delivery log the way Material Tracking does, from a drone flight instead of a walk-through, gets you the same reconciliation without re-walking the yard every time a cert comes in.

Most reconciliation disputes trace back to a tag that fell off, a bundle that got restacked, or a heat lot that shipped in two trucks and got billed as one. The fix is the same either way: count what's stacked, by heat number, before you argue about what the invoice says you owe.

If keeping a current, countable record of the yard sounds better than another walk-through with a clipboard, that's exactly what Material Tracking is built to hand you.

Start a pilot

← Back to the blog